Pricing & AvailabilitySRW-115 SERIES
 

<< Back to main

115 WATTS

 

SRW-115 SERIES

     

 OUTPUT SPECIFICATIONS 
Features
  • Universal 85-264 VAC Input
  • High Efficiency
  • Compact 4025" X 7" X 1.25" Size
  • 2 Year Warranty
  • Fits 1U Applications
  • One to Four Outputs
  • EN 60950 ITE Certification
  • Class B Emissions Per EN 55022
  • Optional Chassis & Cover

Total Output Power at 50o C110W
Output Voltage CenteringOutput 1:         +/-1.0%
Output 2:         +/-5.0%
Output 3:         +/-5.0%
Output 4:         +/-5.0%
(All outputs at 50% rated load)
Source RegulationOutputs 1-4: 0.5%
Load RegulationOutput 1: 1.0% (10-100% Load Change)
Output 2: 5.0% (10-100% Load Change)
Output 3: 5.0% (10-100% Load Change)
Output 4: 5.0% (10-100% Load Change)
Cross RegulationOutput 2: 5.0% Output 1 load varied 50-100%
Output 3:            5.0%
Output 4:            5.0%
Output Voltage Adjust Range Output 1: 95-105%
              
Output NoiseOutputs 1-4: 1%
Turn On OvershootNone
Transient Response  Outputs 1-4
Voltage Deviation 5.0%
Recovery Time     2mS
Load Change       50% to 100%
Output Overvoltage Protection (Optional)Output 1: 110% to 150%
Output Overpower ProtectionOutputs 1-4:     110% Min
Outputs cycle on/off, auto recovery
Hold Up Time16 mS min., 115W, 120V Input
Start Up Time 1 Second
  GENERAL SPECIFICATIONS 
Dielectric Strength 
Reinforced Insulation4242 VDC, Primary to Secondary, 1 Sec.
Basic
Insulation
2121 VDC, Primary to Ground, 1 Sec.
Operational Insulation500 VDC, Secondary to Ground, 1 Sec.
Power Fail Signal
(optional)
Logic low with input power failure 2mS minimum prior to output 1 dropping 1%
Mean Time Between Failures150,000 Hours min., MIL-HDBK-217F, 25oC, GB
Weight1.30 Lbs.  Open Frame
2.25 Lbs.  Chassis and Cover
  INPUT SPECIFICATIONS 
Source Voltage85-264 Volts AC
Frequency Range47-63 Hz
SourceCurrent
True RMS
Peak Inrush

3.5A at 85V Input
40A
Efficiency.72-.80 (Varies by model)
  ENVIRONMENTAL SPECIFICATIONS 
Ambient Operating Temperature Range0oC to +70oC Derating: See Power Rating Chart
Ambient Storage Temp. Range-40oC to +85oC
Temperature CoefficientOutputs 1-4: 0.02%/oC
Conducted EmissionsEn55022 Class B

 
 ELECTROMAGNETIC COMPATIBILITY
Electrostatic DischargeEN 61000-4-2+/-8kV Contact Discharge
+/-8kVAir Discharge
Radiated Electro-magnetic Field EN 61000-4-380MHz-2.5GHz, 10V/m, 80% AM
EFT/BurstsEN 61000-4-4+/-2kV
SurgesEN 61000-4-5+/-1 kV Differential Mode
+/-2 kV Common Mode
Conducted ImmunityEN 61000-4-6.15-80MHz., 10V, 80% AM
Voltage Dips and InterruptionsEN 61000-4-1130% Reduction
95% Reduction
60% Reduction
95% Reduction
Radiated EmissionsEN 55011/22Class B
Conducted EmissionsEN 55011/22Class B
Harmonic Current EmissionsEN 61000-3-2 
Voltage Fluctuations and FlickerEN 61000-3-3 
  MODEL LISTING
ModelOutput 1Output 2Output 3Output 4
SRW-115-4001+5V/12A-5V/4A+12V/4A-12V/2A
SRW-115-4002+5V/12A+24V/1A+12V/4A-12V/2A
SRW-115-4003+5V/12A-5V/4A+15V/3A-15V/2A
SRW-115-4004+5V/12A+24V/1A+15V/3A-15V/2A
SRW-115-4005+5V/12A+12V/1A+24V/3A-12V/1A
SRW-115-4006+5V/12A+12V/3A+15V/2A-15V/2A
SRW-115-4007+5V/12A+12V/2.5A+24V/2A-5V/1A
SRW-115-4008+24V/12A+5V/3A+5V/2A-24V/2A
SRW-115-4011+5V/5A+15V/1A+24V/5A-15V/1A
SRW-115-4013+5V/13A+5V/5A+12V/3A-5V/3A
SRW-115-4012+5V/5A+12V/1A+24V/3A-12V/1A
SRW-115-4014+3.3V/12A+5V/4A+15V/3A-15V/2A
SRW-115-4015+3.3V/12A+5V/4A+12V/4A-12V/2A
SRW-115-4016+5.2V/12A+12V/4A-12V/2A-2V/9A
SRW-115-40175V/8A19V/1A19V/2A54.5V/.5A
SRW-115-401915V/3A-15V/2A+24V/2A3.3V/1A
SRW-115-402015V/3A-15V/2A+36V/1.5A3.3V/1A
SRW-115-41025V/12A12V/2A+12V/4A-12V/25A
SRW-115-3001+5V/12A +12V/4A-12V/2A
SRW-115-3002+5V/12A +15V/4A-15V/2A
SRW-115-3003+5V/12A +24V/3A-12V/1A
SRW-115-3004+5V/12A+24V/1A+12V/6A 
SRW-115-3005+15V/3A-15V/2A+24V/2A 
SRW-115-3006+15V/3A-15V/2A+36V/1.5A 
SRW-115-3007+15V/14A-5V/4A+12V/4A 
SRW-115-2001+5V/12A +24V/3A 
SRW-115-2002+12V/5A  -12V/5A
SRW-115-2003+15V/5A  -15V/5A
SRW-115-2004+24V/2.5A  -24V/2.5A
SRW-115-2005+5V/12A +15V/5A 
SRW-115-2006+5V/12A +12V/5A 
SRW-115-2007+17V/3.4A  -17V/3.4A
SRW-115-2008+9.25V/6A  -9.25V/6A
SRW-115-2010+7.5V/10A  -7.5V/6A
SRW-115-2011+28V/2A  -28V/2A
SRW-115-2012+12V/8A  12V/2A
  Notes 
Consult factory for alternate output configurations.
Consult factory for positive, negative or floating outputs.
Refer to Application Information for complete output power ratings.

All specifications are maximum at 25o C unless otherwise stated and are subjected to change without notice.
Specify optional chassis and cover, power fail, overvoltage protection or DC Input when ordering.
TUV only: SRW-115-3004, SRW-115-3005, SRW-115-4016, SRW-115-4019, SRW-115-4020
UL, CUL only: SRW-115-2011, SRW-115-4007, SRW-115-4008, SRW-115-4012
  SAFETY SPECIFICATIONS 
General Protection Class:

I

Overvoltage Category:

II

Pollution Degree:

2

Underwriters
Laboratories
File E137708
UL 60950, Third Edition
 
 
UL Recognition Mark for Canada
File E137708
CAN/CSA-C22.2 No. 60950:00
 
 
TUVEN 60950:2000
 
 
 Low Voltage Directive
CB Report per IEC 950(1991)
Second Edition A1, A2 and
All national deviations
 
  SRW-115 SERIES MECHANICAL SPECIFICATIONS 

 

  APPLICATIONS INFORMATION
  1. Each output can deliver its rated load but total output power must not exceed 115 watts.
  2. Semiconductor case temperatures must not exceed 110o C.
  3. Sufficient area must be provided around the convection cooled power supplies to allow natural movement of air to develop.
  4. This product is intended for use as professionally installed component within information technology and medical equipment.
  5. A minimum load of 20% is required on output one to insure proper regulation of remaining outputs. 
  6. Peak to peak output ripple and noise is measured directly at the output terminals of the power supply, without the use of the probe ground lead or retractable tip, 20 MHz bandwidth.
  7. This product was type tested and safety certificated using the the dielectric strength test voltages listed in Table V
    of UL 60601-1. In consideration of clause 20.4g, care must be taken to insure the voltage applied to a reinforced insulation
    does not over stress basic insulation. Secondary to ground capacitors may need to be removed prior to performing
    a dielectric strength type test on the end product. It is highly recommended that the DC test voltages listed in DVB.1. Annex DVB are not exceeded during a production-line dielectric strength
    test of the assembled end product. Please consult factory for further information.
  8. This power supply has been safety approved and final tested using a DC dielectric strength test. Please consult factory before performing an AC dielectric strength test.
  9. Maximum screw penetration into chassis mounting holes is .250 inches.
 
 

 Maximum Output Power vs. Ambient Temperature

 
  CONNECTOR SPECIFICATIONS
TB1AC Input
 
.156 friction lock header mates with Molex 09-50-3051 or equivalent crimp terminal housing with Molex 08-50-0189 or equivalent crimp terminal.
TB1DC Output.156 friction lock header mates with Molex 09-50-3101 or equivalent crimp terminal housing with Molex 08-50-0189 or equivalent crimp terminal.
PF power fail signal
TB2-7,8power fail signal return
  RECOMMENDED AIR FLOW DIRECTION
  1.Optimum  2.Good  3.Fair